12V Or Customized Electric Cartridge Heater For Meltblown Machine

12V Or Customized Electric Cartridge Heater For Meltblown Machine

Product detail Material General Information AUSTIN Heating Technology manufactures custom made cartridge heaters for any application. Electric cartridge rod heaters are a versatile and economical heat source for a wide variety of industrial and commercial applications. Standard tube diameters...

Product detail

t6

HTB1MSoaXkxz61VjSZFrq6xeLFXad

n7

HTB1PdMpaBSD3KVjSZFqq6A4bpXaD 

Material

T8


General Information

AUSTIN Heating Technology manufactures custom made cartridge heaters for any application. Electric cartridge rod heaters are a versatile and economical heat source for a wide variety of industrial and commercial applications.

 

Standard tube diameters are 6mm, 8mm, 10mm, 12mm and 16mm, but other special sizes are available for cartridge heaters. Depending on the diameter, lengths can be supplied up to 6000mm. Standard sheath materials are Stainless Steel 201, 304, 316 and 321, but special sheath materials may be available based on diameter and size of the element required.

 

Electric cartridge heaters provide superior heat transfer, uniform temperatures, resistance to oxidation and corrosion and long life even at high temperatures. Flexible lead wire extensions or other mounting options are available for specific applications.


Specifications: 

Wattage Tolerance +5%, -10%
Resistance tolerance +10%, -5%
Voltages available 380V,240V, 220V,110V,36V,24V or 12V
Max operating temp870ºC(1600F)
Length tolerance± 2% or 3.2mm (1/8"), whichever is greater.
Camber tolerance1.7mm per meter (0.020" per foot).
Diameter toleranceDiameter at each end may vary +0.05mm -0.1mm (+.002" -.004")
Standard Unheated Area 5-10mm;
Internal thermocoupletype J or K;
Thermocouple LocationDisc End, Sheath, Center of Heater;
Insulation resistance (cold) ≥ 500 MΩ;
Maximum leakage current (cold) ≤ 0.5 mA;
Diameter from 3.0mm to 30mm;

Construction:

1. Steel, stainless steel, copper, or Incoloy sheathed elements. 

2. Element wire situated in proximity to outside surface for maximum heat transfer and minimum internal temperature while preserving good dielectric qualities 

3.Pure magnesium oxide compressed to an optimum density for best heat transfer and electrical insulation at elevated temperatures.

4Weld connection. 

5. Cold pin 

6. Insulator. 

7. Standard post terminal.

Characters:

1.Resistor core assembly is accurately spaced close to the outer sheath for efficient heat transfer.
2.Initial heater diameter is reduced, thus increasing the density of the assembly, resulting in a heating source which exhibits exceptional dielectric strength and heat transfer characteristics.
3.End disc is always welded in place, preventing contaminants from entering the heater.

 

Application:

* Medical: Dialysis, Sterilization, Blood Analyzer, Nebulizer, Blood/Fluid Warmer, Temperature Therapy
* Telecommunications: Deicing, Enclosure Heater
* Transportation: Oil/Block Heater, Aircraft Coffee Pot Heaters,
* Food Service: Steamers, Dish Washers,
* Industrial: Packaging Equipment, Hole Punches, Hot Stamp.

 

*Water Heating:We recommend 10 watts per square centimetre when cartridges are to be immersed in water because the water removes the energy from the element very effectively. Commonly used as a chemical solutions heater.

*Oil Heating:Commonly used as engine sump heaters. When heating some oils, only 2 watts per square centimetre can be used otherwise the high cartridge heater surface temperature causes the oil to oxidise and carbon to be built-up on the surface of the heater. When this occurs, the carbon can thermally insulate the cartridge heater, causing the unit to heat up internally, often resulting in electrical failure.

 

*Air Heating:Elements of approximately 1 watt per square centimetre are suitable for convection air heating, eg. Anti-condensation heaters.

 

*Die Heating:Manifolds, hot runners and torpedoes.

 

*Packaging:Hot melt glue applicators.

d1

360截图20200601171142193

Pls advise when inquiry:

1.Type of Cartridge Heater (please refer to Termination Options)

2.Ø of Cartridge Heater.

3.Overall length for a straight Cartridge Heaters.

4.Wattage & Voltage

5.Lead type ( glass fibre / PTFE ) & lead length.

Other product

7

H8

Cerificate

image


Serving

d2

Contact us

Shenzhen Superb Heater Technology Co.,Ltd
ADD: No.8, Third Industrial Zone,Shiyan Town,Baoan District,Shenzhen City,China 
Tel/Fax: 0086-755-29059861
Mobil/Whatsapp: +86 18815481562
Web: www.superbheater.com






Superb Heater Technology has been focused on the production of 12v or customized electric cartridge heater for meltblown machine since 1985, which is well-known as one of the leading manufacturers and suppliers of 12v or customized electric cartridge heater for meltblown machine. In the past years, we owned strong reputation for the high quality, reliable performance and strong durability of our products. Should you are interested, please feel free to contact our factory.

Previous: Customize Industrial 220V 300W Pencil Cartridge Heater For Melt-blown Fabric Machine

Next: Nonwoven Meltblown Cloth Air Duct Heater